COMPARATIVE ANALYSIS AND OPTIMIZATION OF FRICTION STIR WELDING PARAMETERS FOR AA6351 ALUMINUM ALLOY: AN APPROACH USING AgNO3 NANO COATINGS

Authors

  • T. Vijaya Kumar Research Scholar, Department of Mechanical Engineering, Osmania University, Hyderabad Author
  • Dr. PVR. Ravindra Reddy Professor, Mechanical Engg. Dept. CBIT Author
  • Dr. A. Krishnaiah Sr. Professor, Department of Mechanical Engineering, University College of Engineering, Osmania University, Hyderabad Author

Abstract

Friction Stir Welding (FSW) is a solid-state joining process that is widely utilized for aluminum alloys due to its superior mechanical properties and efficiency in aerospace and structural applications. This study investigates the impact of key FSW process parameters on the weld quality of AA6351 aluminum alloy, with and without silver nitrate (AgNO₃) Nano coating. The primary objective is to determine the optimal welding conditions that enhance tensile strength, hardness, and fatigue resistance using the Taguchi L27 experimental design. The experiments were conducted with, perhaps the highest welding speed reported, so far. Through the analysis, optimum combinations of the parameters were suggested for each material at a high speed friction stir window. The selected parameters were tool rotational speed, welding speed, and tool pin profile, each evaluated at three distinct levels. AgNO3 Nano coatings were applied to a set of samples to assess its impact on the welds. The welded samples were then subjected to a series of tests, including tensile strength testing, hardness measurement, and microstructural analysis using optical microscopy and scanning electron microscopy (SEM). This study also investigates the optimization of FSW parameters for AA6351 aluminum alloy using AgNO3 coated nanoparticles as coatings. Mechanical properties were evaluated through tensile tests, hardness measurements, and fatigue tests. Experiments were conducted by welding AA6351 aluminum alloy plates under varying process conditions

References

Reghubabu et.al (2008) An experimental study of the effect of welding parameters on mechanical and microstructural properties of AA6082 - T6 friction stir welded butt joints. APN journal of engineering and applied science, 3 (5), 68 – 74,2008.

Zhang, et.al (2012) Effect of welding parameters on microstructure and mechanical properties of friction stir welded 2219 Al- T6 joints. Journal of Material science, 47, 4075 – 4086,2012.

Sreenivas, et.al (2017) Effect of applied axial force on FSW of AA 6082- T6 Aluminium alloys. International Journal of Mechanical Engineering and Technology, 8, 88 – 99,2017.

Ashwani Kumar, et.al (2014) Influence of Tool Shoulder Diameter on Mechanical Properties of Friction Stir Welded Dissimilar Aluminium Alloys 2014 and 6082. International Journal of Surface Engineering & Materials Technology, 4 (1), 5 – 10,2014.

Sung-Wook Kang, et.al (2015) Residual stresses analysis of friction stir welding using one-way FSI simulation. Journal of Mechanical Science and Technology, 29(3), 1111–1121,2015.

Scialpi, A. et.al (2007) Influence of shoulder geometry on microstructure and mechanical properties of friction stir welded 6082 aluminium alloy. Materials and Design, 28, 1124 – 1129,2007.

Amèvi Tongne et.al (2015) Banded Structures in Friction Stir Welded Al Alloys. Journal of materials processing technology, 221, 269 – 278,2015.

Podrzaj, et.al (2015) Welding defects at friction stir welding. Metalurgija, 54 (2), 387 – 389,2015.

Pradeep, et.al (2014) Defect Analysis Of Friction Stir Welded Steel Plates On Different Tool Profiles. International Journal of Mechanical And Production Engineering, 2 (7), 92 – 98,2014.

Patil, et.al (2010), Experimental study on the effect of welding speed and tool pin profiles on AA6082-O aluminium friction stir welded butt joints. International journal of engineering, science and technology, 2(5), 268 – 275,2010.

Arora, (2012) ‘Load bearing capacity of tool pin during friction stir welding’, Int. J. Adv. Manuf. Technol., vol. 61, no. 9-12, pp. 911–920, ISSN:0268-3768,2012.

R. Palanivel, et.al (2014) “Mechanical and metallurgical properties of dissimilar friction stir welded AA5083- H111 and AA6351-T6 aluminium alloys” Transactions of Nonferrous Metals Society of China Volume 24, Issue 1, January 2014, Pages 58-65,2014.

Avinash P et.al(2015) “Friction stir welded butt joints of AA2024 T3 and AA7075 T6 aluminium alloys” MRS Singapore - ICMAT Symposia Proceedings 7th International conference on materials for advanced technology,2015.

Babu, et.al (2010). An expert system for predicting the deep drawing behavior of tailor welded blanks. Expert Systems with Applications, 37(12), 7802-7812. https://doi.org/10.1016/j.eswa.2010.04.059,2010.

Ashok Kumar, et.al(2014), ‘Optimization of friction stir welding process parameters to maximize tensile strength of stir cast AA6061-T6/AlNp composite’, Materials & Design, vol. 57, no. 1, pp. 383–393, ISSN: 0264-1275,2014.

Arbegast et.al (2007) ‘Friction Stir Welding and Processing’, ASM International, New York, pp. 273– 308,2007.

Benavides, et.al (1999) ‘Low- temperature friction-stir welding of 2024 aluminum’, Scripta Mater, vol. 41, no. 8, pp. 809–815,1359-6462,1999.

Aval, et.al (2015)‘Influences of pin profile on the mechanical and microstructural behaviors in dissimilar friction stir welded aluminum AA6082–AA7075 butt joint’, Mater. Des., vol. 67, no. 1, pp. 413–421, ISSN: 0264-1275,2015.

Bendzsak, et.al(2000), Effect of SiC Particle Addition on Mechanical Properties of Friction Stir Welded Aluminum Alloys ‘Proceedings of the Second International Symposium on Friction Stir Welding’, Gothenburg, Sweden, June 26–28,2000.

Aslan, et.al(2008) ‘Application of response surface methodology and central composite rotatable design for modeling and optimization of a multi-gravity separator for chromite concentration’, Powder Technology, vol. 185, no. 1, pp. 80–86, ISSN:0032-5910,2008.

Cabibbo, et.al (2020). New approaches to friction stir welding of aluminum light-alloys. Metals, 10(2), 233,2020. https://doi.org/10.3390/met10020233

Adamowski et.al (2007) Analysis of FSW welds made of aluminium alloy AW6082-T6. Archieves of material science and engineering, 28 (8), 453 – 460,2007.

Bertrand, et.al (2019) ‘Optimization of Friction Stir Welding Parameters for Wear Properties of Dissimilar Aluminum Alloys, vol. 271, no. l, pp. 312.324, ISSN: 0924-0136,2019.

Abd Elnabi, et.al (2019) ‘Influence of friction stir welding parameters on metallurgical and mechanical properties of dissimilar AA5454–AA7075 aluminum alloys’, Journal of Materials Research and Technology, vol. 8, no. 2, pp. 1684-1693, ISSN:2238-7854,2019.

Amancio-Filho, et.al (2008) ‘Preliminary study on the microstructure and mechanical properties of dissimilar friction stir welds in aircraft aluminium alloys 2024-T351 and 6056-T4’, Journal of Materials Processing Technology, vol. 206, no. 1-3, pp. 132–142, ISSN:0924-0136,2008.

Downloads

Published

2026-04-04