COMPARISON OF SEISMIC BEHAVIOR OF A STRUCTURE WITH COMPOSITE COLUMNS AND STEEL COLUMNS BY USING E-TABS SOFTWARE

Authors

  • Arava Pavan Student, Department of Civil Engineering, Bheema Institute of Technology and Science, Adoni, A.P Author
  • Mr. A Vishnu Assistant Professor, Department of Civil Engineering, Bheema Institute of Technology and Science, Adoni, A.P Author

Keywords:

non-linear, performance point, pushover, and ETABS.

Abstract

Most building structures are made of reinforced 
concrete, which is mostly determined by the 
accessibility of the component materials, the 
degree of construction expertise needed, and the 
applicability of design regulations.  Due to its 
dangerous formwork and high dead load, R.C.C. 
is 
no longer cost-effective.  
Nonetheless, 
composite construction is a novel idea in the 
building sector.  Delaying the building of each 
floor while concrete columns are cast may be 
economically prohibitive due to the usage of 
contemporary composite technologies, which 
enable the creation of multi-story structural 
frames to continue at a rapid rate.  However, 
composite beam-columns' greater earthquake 
resistance has long been acknowledged in Japan, 
where they are now often used in building.  
Therefore, in order to promote the adoption of 
this 
effective kind of mixed construction, 
seismic design standards for commonly used 
Indian structural systems have to be developed.  
This project compares different building 
characteristics.  
This research uses ETABS to study a residential 
G+15 multi-story building for pushover analysis, 
assuming that linear, static, and dynamic 
analysis of material properties is carried out.  
Several metrics, including displacement, storey 
drift, performance point, and base shear, are 
shown as part of these non-linear analyses.  
These days, it is essential that all structures be 
examined and built to withstand lateral pressures 
like wind and earthquakes.  However, in the 
construction of multistory buildings, it is often 
seen that the cross sectional area of RCC 
structural members comes out quite heavy with a 
big quantity of component material, such as steel 
& concrete, which takes up a lot of space.  One 
of the greatest solutions in these situations is a 
composite construction, which not only protects 
against seismic stresses but also reduces the 
cross sectional area of structural members and 
offers a lot of space for economical use. 

References

IS 1893 (Part 1): (2002), “Criteria for Earthquake Resistant Design of Structures Part 1 General Provisions and Buildings”, Bureau of Indian Standards.

CSI Computers and Structures INC. “Introductory Tutorial for E-TABS: Linear and Nonlinear Static and Dynamic Analysis and Design of Three- Dimensional Structures” 2011

CSI (2009). “E-TABS: Static and Dynamic Finite Element Analysis of Structures” Nonlinear Version 14, Computers and Structures.

B.C. Punmia, A.K. Jain, 2006, “R.C.C Designs”, Laxmi publications New Delhi. IS-456 2000plain and reinforced concrete code of practice.

P. Agarwal, M. Shrikhande, Earthquake resistance design of structures, PHI learning Pvt. 2012.

Theory of Structures by Ramamrutham for literature review on kani′s method Reinforced and slab.concrete Structures by A.K. Jain and B.C. Punmia for design of beams, columns ETABS Version 9.70 (1997), Computers and Structures, Inc., Berkeley, California. International Code Council, Inc. (2000). International Building Code.

B. K. Sanghani and P. G. Patel, “Behaviour of Building Component in Various Zones,” International Journal of Advances in Engineering Sciences, Vol. 1, Issue 1(Jan. 2011).

Simu, E and Miyata, T. (2006), “Design of buildings and bridges for wind a practical guide for ASCE-7 standard users and designers of special structures, John Wiley & Sons.

Sinha, S.N., Handbook of reinforced concrete design, 1996, Tata McGraw-Hill Publishing Company limited, New Delhi 110 008.

Downloads

Published

2026-06-10